1PC Automatic Household Grinding Wheel Knife Grinder MTKN-001V3 Electric Knife Sharpener Hotel Restaurant Knife Grinding Machine

1PC Automatic Household Grinding Wheel Knife Grinder MTKN-001V3 Electric Knife Sharpener Hotel Restaurant Knife Grinding Machine

Product parameters

Model: MTKN-001V3

Rated voltage: 220V

Rated frequency: 50Hz

Rated power: 60W

Shell material: ABS

Product net weight: 1.407kg

Product size: 245*110*100mm

Sharpening stone: brown corundum

Coarse grinding wheel: brown corundum (A)

Fine grinding wheel: green silicon carbide (A)

Safe temperature control:

    When the knife sharpener is used continuously, the temperature controller will automatically stop working when the temperature in the machine body reaches about 77°C, which automatically protects the motor from burnout. The machine switch light is on, but the grinding wheel is not working. You need to wait for the temperature to drop before you can turn it on again.

Note:

    Unsuitable knives: ceramic knives, Damascus knives, serrated knives, scimitars, sickles, axes and other knives with non-straight blades.

    Not applicable to scissors: decorative scissors, comb-tooth scissors, special-shaped scissors and other non-straight or single-piece scissors whose thickness exceeds the slot limit.

Picture showing:

Grinding method:

Ensure that the grinding direction of the tool is from the position close to the tool handle to the tip of the tool,

and then lift the tool to repeat the above work, and it is forbidden to drag back and forth in the groove for grinding.

Note:

Unsuitable knives: ceramic knives, Damascus knives, serrated knives, scimitars, sickles, axes and other

knives with non-straight blades.

   Not applicable to scissors: decorative scissors, comb-tooth scissors, special-shaped scissors and other

non-straight or single-piece scissors whose thickness exceeds the slot limit.

Rough sharpening of the knife edge (No. 1 and No. 2 slot)

Applicable for rough grinding: Unopened or stewed knives can quickly grind the thickness of the blade to the thickness required for the sharpness of the blade.

It is recommended to sharpen the knife at a speed of 3~4cm/sec

1. Put the tool in the No. 1 rough grinding groove to grind the right blade. The blade is close to the straight wall of the groove and extends downwards until the blade touches the grinding wheel. Ensure that the tool grinding direction is from the position close to the tool holder to the tool tip position, and then lift the tool

(It is not possible to drag back and forth in the groove for grinding).

2. Lift the tool and place it in the No. 2 rough grinding slot to grind the left edge of the blade, and grind in the slot 1 and 2 continuously until the blade is sharp. The number of repeated cycles depends on the sharpness of the original cutting edge of the tool.

Fine sharpening of the knife edge (No. 3, No. 4 slot)

Application for fine grinding: daily tool blade maintenance, rough grinding of the tool after opening, and then fine grinding to remove iron swarf to achieve the effect of sharp blade

Scissors grinding

    Open the scissors, press the inner plane of the left blade of the scissors to the upper straight wall of the groove, the blade is facing the grinding wheel, and slowly approach the scissors to the grinding wheel until the blade touches the grinding wheel. Make sure that the direction of the scissors grinding is from the position close to the handle body to the sharp position, and then take out the scissors (cannot be dragged back and forth in the groove for grinding), the grinding speed is recommended to be 3~4cm/sec, and then Operate the right edge of the scissors according to the above steps, and cyclically sharpen the left and right edges until the scissors are sharp.

Flat-blade screwdriver sharpening

    Put the flat-blade screwdriver in the special grinding hole for grinding (the screwdriver should not be too large, it should be able to extend into the hole). Slowly extend the screwdriver gently toward the grinding wheel until it touches the grinding wheel for grinding, and the screwdriver is sharpened. Shaving can only flatten the one-word mouth. Don't insert the screwdriver too hard to avoid damage to the sharpener and human injury.

Debris drawer

    Equipped with two chip loading cabinets, the chips generated after sharpening can be taken out through the chip loading cabinet at the back of the sharpener, which is convenient and quick. When cleaning, you only need to pull out the chip cabinet to clean up the debris. The wear debris should be cleaned up in time. It is recommended to clean it after each grinding to avoid too much wear debris from accumulating in the fuselage.

Steps to change the grinding wheel autonomously

1. With the bottom facing up, pull out 4 suction cups

2. Remove 8 screws from the cross

3. Open the shell to reveal the machine components

4. Remove the nut to replace the grinding wheel

Note: If your area is a remote area, you will need to add a separate fee.

Notice : when the parcel arrived to your customs,please pay the tax and pick up the parcel,
we are not responsible for  any customs duty or import tax